How To Install Delta Shower Repair Kit

Repairing your old Delta shower faucet is a somewhat easy job, even if you're not very skilled with home improvement projects. Every bit long as you lot take the correct tools and you follow the steps hither, you'll get your shower faucet working right in no time.

Delta shower faucets are one of the most pop brands on the marketplace due to their uncomplicated design, their performance, and their lifetime warranty. The best part? Acquiring spare parts is inexpensive and fairly piece of cake to do. In fact, almost domicile improvement stores carry Delta shower faucet parts. Otherwise, they're too easily found online on sites like Amazon and Ebay.

Earlier you lot purchase the parts yous demand, brand sure yous know specifically what make and model yous have in your shower. If you tin't find the parts in stores or online, you'll have to purchase a whole new faucet kit.

1 ➜ Handle
2 ➜ Handle Button
3 ➜ Handle
iv ➜ Cap Assembly
5 ➜ Rectangular Cam
vi ➜ Triangular Cam
seven ➜ Packing
viii ➜ Steel Ball with Round Pivot
9 ➜ Steel Brawl with Diamond Shaped Pin
10 ➜ Seats & Springs
11 ➜ Balancing Spool
12 ➜ Button Diverter
thirteen ➜ Screws
14 ➜ Escutheon

Repairing your former Delta faucet

For homeowners who have an old Delta shower faucet that'south giving them problems, it's better simply to become ahead and purchase a whole new Delta faucet kit. Once you have your kit, follow these directions.

Turn off the h2o supply to your shower. Nearly showers don't have single supply valves. Every bit a upshot, the water to the entire house will need to exist turned off. You can do this by locating the archway valve and turning it off.
Go outside and turn on whatsoever of your home'southward wall hydrants or faucets. Let information technology run for a few minutes. This volition bleed your dwelling's water supply. Caput back inside and turn on the shower faucet. This will also assist drain the last of the leftover water. You'll now desire to remove the handle. Typically, y'all'll need an Allen wrench to remove the handle (1 & 2). If you're unsure how to do this, read the owner'due south manual.
After you take removed this spiral, the bonnet nut will besides take to be removed. Utilize a strap wrench to practise this. If your faucet is one-time, the bonnet nut may exist tough to become off. You tin can use a picayune lubricant to loosen it up. After the nut is off, remove the bonnet. At present take off the cam (five & 6) and brawl (viii & 9) assembly which is located under the bonnet.
Equip yourself with a pair of fine tweezers. You lot can also utilize a abrupt pick also. With either of these tools, remove both the springs and the safe seats (10). You'll find these located within the faucet housing.
Once you have removed both the springs and the seats, inspect the inside of the housing. What you want to look for are cracks or calcium build-ups. The calcium build-upwardly tin can be removed with the picks. Take the new seats and lubricate them up. Information technology's important to annotation that you should never use petroleum jelly. Vegetable oil and silicone grease are both effective lubricants.
Insert the springs into the seats. Brand certain that y'all insert the springs with the small side in. With either your screwdriver or your choice, insert both the seat and the spring into the housing of the faucet.
Have the ball assembly and lubricate it up. Once lubricated, insert it into the housing and make sure it'southward aligned properly. The cam volition at present need to be placed on the ball assembly. Make certain the trivial tab located on the side is completely inserted into the housing slot.
While holding the cam down with your finger, you lot'll want to thread the bonnet back on and then tighten it with your strap wrench. Reconnect the handle. Turn off the faucet you lot're working on.
Next, plough on your home'due south water approximately i-third of the way. This will allow your pipes to slowly fill up. It's very important not to plough the water on full blast at first. Doing and then could cause the calcium that's built upward on the inside of the pipes to break off and grade a clog. Later on all the air has been removed from the pipes, yous can plough information technology on all the way. Inspect your shower faucet for leaks and other bug.

Replacing an old Delta valve cartridge

A modify in water force per unit area, sudden changes from hot to common cold, and consistent leaking can all exist a result of a faulty valve cartridge. If you know this is the problem, so instead of replacing the whole unit of measurement, you can simply but change the valve cartridge. And then, how do you do this?

With the handle removed, remove the trim sleeve and so the spacer. These both should come off pretty like shooting fish in a barrel.
Now yous'll want to remove the bonnet nut with due south strap wrench.
Take hold of onto the valve cartridge and jerk it back and forth while also pulling on information technology. With a footling effort, information technology should come right out.
Take your new cartridge and insert it. Withal, when inserting this piece, install the new cartridge making certain the side marking labeled "hot" is on the side of the valve where the hot water comes from.
You'll now want to line up the keys on the side with the slots plant in the valve.
Take the bonnet nut and hand screw it dorsum on until it'southward snug.
Put the handle back on.
You accept now replaced your valve cartridge. Again, turn your water on slowly, get out all the air, and bank check for leaks.

Author
Contempo Posts

Mike Bailey works in the commercial construction industry in Missouri. He also enjoys writing construction and home improvement related manufactures.